Difference between revisions of "PBMinutes"
m |
m |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 29: | Line 29: | ||
*step 11) add a LED, EL, matrix or other type of back light to illuminate this assembly | *step 11) add a LED, EL, matrix or other type of back light to illuminate this assembly | ||
| − | '''Make new front panel''' (1 hour DYE) | + | [done]'''Make new front panel''' (1 hour DYE) |
*cut wood to size | *cut wood to size | ||
*cut plastic to size | *cut plastic to size | ||
| Line 56: | Line 56: | ||
*install combi-lock | *install combi-lock | ||
| − | '''Need Foot Stands''' (30 mins DYE) | + | [done]'''Need Foot Stands''' (30 mins DYE) |
*Lathe | *Lathe | ||
*4 Delrin holes | *4 Delrin holes | ||
| − | '''Need a curtain and backdrop''' (FRI) | + | [done]'''Need a curtain and backdrop''' (FRI) |
| − | '''Order battery''' (FRI) | + | [done]'''Order battery''' (FRI) |
Need to add Threaded Rivets for Future Expansion | Need to add Threaded Rivets for Future Expansion | ||
| Line 73: | Line 73: | ||
Need lift handles | Need lift handles | ||
| − | Need to buy backdrop | + | [done]Need to buy backdrop |
[done]Need wheels | [done]Need wheels | ||
| Line 80: | Line 80: | ||
[done]Need to buy and laminate wood | [done]Need to buy and laminate wood | ||
| + | |||
| + | 100% reliability | ||
| + | We cannot tolerate technologies that do work 100% of the time so we will not support OS based technologies or wifi networked based solutions where a tether to the web is required. | ||
| + | |||
| + | http://itunes.apple.com/us/app/dslr-camera-remote-professional/id316771002?mt=8# | ||
Latest revision as of 06:55, 18 May 2012
[done]Camera Z Mount knobs hit each other (30min DYE)
- Turn the second hole into a slot so it looks intentionally adjustable
- Re-drill holes wider? (makes it look unintentional)
[done]Camera Z Mount is too long (1hour DYE)
- De-rivet right angle
- Cut aluminum section
- re drill, re-rivet piece in
Mount in Camera support rails (30min FRI)
- drill slide rail holes
- Rivet into box
Make Cap touch Sensor (1 hour DYE)
- step 1) print out a stencil
- step 2) tape a copper sheet onto the back of the stencil
- step 3) cut out stencil
- step 4) apply PSA to top of the copper tape
- step 5) peel off PSA protector and stick to polyethalyne
- step 6) scratch off paper using knife or water (only enough to solder to)
- step 7) solder a 30awg or smaller wire to that electrode
- step 8) add a female header socket to the end of the 30 gauge wire
- step 9) add more PSA
- step 10) add 1/4" polyethalyne to back of sensor to protect it
- step 11) add a LED, EL, matrix or other type of back light to illuminate this assembly
[done]Make new front panel (1 hour DYE)
- cut wood to size
- cut plastic to size
- apply adhesive to surface and install window
Install Monitor (2 hour FRI)
- Cut out hole
- Design and install retention system
- must be removable
Need LED Ring (4 hours FRI)
- make template
- stack 3 1/8" sheets together
- cut out template
- drill 40 holes
- Wire in 40 LEDs common cathode.
- Wire 5 drive circuits
Need to design door (2 hours DYE)
- Need to cut door out
- install piano hinge
- install rigid extrusions
- install backing
- install combi-lock
[done]Need Foot Stands (30 mins DYE)
- Lathe
- 4 Delrin holes
[done]Need a curtain and backdrop (FRI)
[done]Order battery (FRI)
Need to add Threaded Rivets for Future Expansion
Need to add top optical exit window for vertical flash system
Need a mechanism to lock booth down
Need lift handles
[done]Need to buy backdrop
[done]Need wheels
[done]Need pull handle
[done]Need to buy and laminate wood
100% reliability We cannot tolerate technologies that do work 100% of the time so we will not support OS based technologies or wifi networked based solutions where a tether to the web is required.
http://itunes.apple.com/us/app/dslr-camera-remote-professional/id316771002?mt=8#
